Brand Logo Reactive Resin Engineering / Tour-Validated Bowling Systems

Cybex Equipment Buying Guide: Three Gym Scenarios, Three Different Answers

No Single Right Answer—But Plenty of Wrong Ones

I'm a quality and brand compliance manager for a commercial gym equipment dealer. I review every spec sheet, delivery, and install packet before it reaches a customer—roughly 400 line items a year. In 2024, I rejected about 12% of first deliveries for spec mismatches, cosmetic defects, or missing documentation.

Gym owners ask me some version of the same question every week: "What's the best Cybex setup for my facility?" The honest answer is that there isn't one. What works for a hardcore strength gym will sit unused in a boutique studio, and vice versa. It took me about three years and 600+ spec reviews to understand that "commercial grade" is a spectrum, not a checkbox.

So instead of a single recommendation, here are the three scenarios I see most often—and what I'd actually do in each.

Scenario 1: You're Building a Strength-First Floor

Your members care about squats, presses, and pulls. They know what a hack squat is and they'll notice if the machine feels off. This is where Cybex's plate-loaded and selectorized strength lines earn their keep.

The hack squat starting weight question

One of the most common questions I get: what does the Cybex hack squat weigh without plates? The frustrating answer is that it depends on which generation and model you're looking at. Cybex has run multiple hack squat designs over the years, and the spec sheets don't always use the same definition of "starting weight."

Here's the trap. Some sheets quote the sled (carriage) weight. Others quote the effective starting resistance at the footplate after the lever ratio. On a 45-degree machine, those numbers can differ by 40–70 lbs. I've seen reps quote one figure and deliver a machine that felt completely different from what the buyer expected. That's a red flag if your rep can't tell you which number they're giving you.

Bottom line: ask for the spec sheet for the exact model and serial number you're buying. If the "starting weight without plates" isn't clearly defined, get it in writing before you sign. In my experience, the unloaded sled on a commercial hack squat is substantial—often in the 150–250 lb range before a single plate goes on. But because the sled travels at an angle, the resistance at the footplate is lower. Don't confuse the two.

Underhand vs. overhand lat pulldown

If you're specifying a lat pulldown station, the underhand vs. overhand debate matters less for the machine and more for your member mix. Overhand (pronated) grip hits the lats with more width and brings in the teres major and lower traps. Underhand (supinated) grip shifts emphasis to the lower lats and involves more biceps.

My recommendation: buy a pulldown with an adjustable or multi-grip bar rather than committing to one fixed handle. A dedicated underhand-only station is a tough sell unless you're running a serious bodybuilding floor. Most general-population members will default to overhand, and the underhand crowd is usually fine with a swap-out bar.

The counterintuitive part: I've seen gyms spend extra on a second pulldown station for grip variety when the real bottleneck was having only one adjustable bench nearby. Fix the flow before you add machines.

Scenario 2: You're Running a Full-Service Club

Your members are a mix—some lift, some do cardio, some just want to feel like they did something. Here, the cardio floor does more of the retention work than the strength floor.

Cybex bike workout programming

Commercial bikes live or die on how quickly a member can start pedaling without a tutorial. Cybex's bike consoles have come a long way, but the workout programming is where gyms either use the machine or ignore it.

My rule: if a member can't get into a decent interval workout within 20 seconds of sitting down, the console is too complicated for your floor. Preset programs are fine, but the ones that actually get used are the simple ones—quick start, a few interval presets, and a heart-rate target. Fancy FTP tests and watt-based protocols are great for coached sessions but rarely get touched in a 24/7 access gym.

Take this with a grain of salt: I'm not a trainer, so I evaluate this from a spec and usability standpoint. But I've watched enough installs to know that the bikes with the simplest default screen get the most hours.

Recumbent cross trainers

Recumbent cross trainers are a specific tool. They're low-impact, easy on the lower back, and great for older members, rehab, and deconditioned populations. If your member base skews 45+, or you have a medical referral pipeline, they're a no-brainer.

If your average member is 28 and chasing PRs, a recumbent cross trainer will collect dust. I've seen clubs buy them because "we should have one of everything" and then move them to a corner within six months. Be honest about who's actually going to use it.

One quality note: check the seat adjustment mechanism before you buy. Recumbent cross trainers take a beating on the seat track, and a wobbly seat is the first thing members complain about. That's a durability issue, not a brand issue—but it's the kind of thing that doesn't show up on a spec sheet.

Scenario 3: You're Space-Constrained or Boutique

You've got 1,500 square feet, a membership that expects a premium feel, and no room for a full dumbbell rack.

Nuobell adjustable dumbbells

The Nuobell is a clever piece of gear. The classic model runs roughly 5 to 80 lbs per hand in 5-lb increments, adjusted by turning a dial. It's compact, fast to change, and looks sharp on a studio floor.

Here's the honest limitation: Nuobells are not meant to be dropped. The internal mechanism doesn't tolerate the abuse that a rubber hex dumbbell shrugs off. If your members do heavy rows and let the weights fall, or if you run circuit classes where people dump dumbbells on the floor, you'll be filing warranty claims within a year.

They're also capped at 80 lbs per hand. For a boutique studio doing moderate loads and controlled tempo work, that's fine. For a strength-focused crowd, it's a deal-breaker.

The counterintuitive advice: rent or borrow a set for a month before you commit. I've seen studios buy six pairs because the demo felt great, then discover members find the dial mechanism "fiddly" and keep reaching for the fixed rack instead. The space savings are real, but they only matter if people actually use the product.

How to Tell Which Scenario You're In

Don't guess. Pull three numbers from your current operation:

  1. Peak-hour equipment utilization. If your cardio deck is full and your strength floor has empty machines, you're Scenario 2, not Scenario 1—regardless of what you want your gym to be.
  2. Member complaints from the last 90 days. Sort them by equipment category. The category with the most complaints is the one to fix first.
  3. Renewal rate by member segment. If your 45+ members renew at 70% and your 25–34 group renews at 40%, your equipment mix is probably speaking to the wrong crowd.

One more thing: check the safety certifications. Commercial strength machines sold in the US should meet ASTM F2216; in Europe, EN 957. Those are baseline standards, not a quality ranking. A machine can pass and still feel like a rental car. The spec sheet tells you it's legal; the install tells you if it's good.

And if you're still on the fence between two configurations, the tiebreaker should be service. Who's going to fix the machine when the cable snaps on a Saturday? That answer matters more than a 5% price difference. I've seen a $22,000 equipment package turn into a $30,000 headache because the service response was slow. Ask about local parts inventory and average response time before you sign anything.

That's the honest version. There's no universal "best" Cybex setup—there's the one that matches your members, your space, and your service reality. Figure out which scenario you're actually in before you spend a dollar.

Author avatar

Jae-Min Park

Jae-Min Park is a bowling-center equipment analyst covering bowling balls, pins, lanes, pinsetters, scoring systems, ball returns, shoes, bags, and maintenance supplies. He uses USBC equipment specifications, ASTM material test methods, and measurable checks for ball mass, circumference, hardness, radius of gyration, lane topography, pin weight, pinsetter cycle time, oil pattern, and scoring accuracy. His work helps center operators, pro shops, mechanics, and buyers compare play consistency, machine uptime, consumable life, serviceability, lane capacity, and tournament suitability.

Leave a Reply